收藏本站
NMXU Series
Isolated 5W Single & Dual Output DC/DC Converters
ISOLATION CHARACTERISTICS
Parameter
Isolation test voltage
Resistance
Conditions
Flash tested for 1 second
Viso= 1000VDC
Min.
1000
1
Typ.
Max.
Units
VDC
GΩ
GENERAL CHARACTERISTICS
Parameter
Switching frequency
Conditions
All input types
Min.
Typ.
70
Max.
Units
kHz
TEMPERATURE CHARACTERISTICS
Parameter
Speci?cation
Storage
Case temperature rise above
Conditions
All output types
5V output types
Min.
0
-55
Typ.
30
Max.
70
100
Units
°C
ambient
Cooling
TOLERANCE ENVELOPE
+10%
All other output types
Free air convection
RoHS COMPLIANCE INFORMATION
20
o Line
T y pica l L
+5%
V NOM
ad
+2.5%
-2.5%
-7.5%
This series is compatible with RoHS soldering
systems with a peak wave solder temperature of
300oC for 10 seconds. The pin termination ?nish
on this product series is Matte Tin over Nickel
Preplate. The series is backward compatible with
Sn/Pb soldering systems.
10
25
50
75
100
Output Load Current (%)
For further information, please visit www.murata-ps.com/rohs
TECHNICAL NOTES
ISOLATION VOLTAGE
‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage,
applied for a speci?ed time, across a component designed to provide electrical isolation, to verify the integrity of that isolation.
Murata Power Solutions NMXU series of DC/DC converters are all 100% production tested at their stated isolation voltage. This is 1kVDC for 1 second.
A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?”
For a part holding no speci?c agency approvals, such as the NMXU series, both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or
60VDC. The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part
could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must
be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-accessible circuitry according to
safety standard requirements.
REPEATED HIGH-VOLTAGE ISOLATION TESTING
It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materi-
als, construction and environment. The NMXU series has toroidal isolation transformers, with no additional insulation between primary and secondary windings of enameled wire.
While parts can be expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel
(typically polyurethane) is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly limited.
We therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from speci?ed test voltage.
This consideration equally applies to agency recognized parts rated for better than functional isolation where the wire enamel insulation is always supplemented by a further
insulation system of physical spacing or barriers.
www.murata-ps.com/support
KDC_NMXU.D01 Page 2 of 3
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
NMXS1205SOC CONV DC/DC 5W 12VIN 5V DIP REG
NOJE687M004RWJ CAP NIOB OXIDE 680UF 4V 2917
NOJX686M006RWJ CAP NIOB OXIDE 68UF 6.3V 2917
NOME687M002R0023 CAP NIOB OXIDE 680UF 2.5V 2917
NOSV108M002R0050 CAP NIOB OXIDE 1000UF 2.5V 2924
NPH10S2405IC CONV DC/DC 10W 24VIN 5.1VOUT DIP
NPH15S2415IC CONV DC/DC 15W24VIN 15.1VOUT DIP
NPH25S2415IC CONV DC/DC 25W24VIN 15.1VOUT DIP
相关代理商/技术参数
NMXD1205SO 制造商:Murata Power Solutions 功能描述:DC/DC CONVERTER 5W +/-5V
NMXD1205SOC 功能描述:DC/DC转换器 12Vin +/-5Vout +/-0.5A 5W DIP Reg RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
NMXD1205U 制造商:Murata Power Solutions 功能描述:DC/DC CONVERTER 5W +/-5V
NMXD1205UC 功能描述:DC/DC转换器 12Vin +/-5Vout 5W +/-0.5A DIP un-Reg RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
NMXD1212SO 制造商:Murata Power Solutions 功能描述:DC/DC CONVERTER 5W +/-12V
NMXD1212SOC 制造商:Murata Power Solutions 功能描述:CONVERTER DC/DC 5W +/-12V
NMXD1212U 制造商:Murata Power Solutions 功能描述:DC/DC CONVERTER 5W +/-12V
NMXD1212UC 功能描述:DC/DC转换器 12Vin +/-12Vout 5W +/-0.208A DIP un-Reg RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: